Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
CUYI plotter cutter
04-27-2011, 11:39 AM (This post was last modified: 04-27-2011 12:38 PM by zenebier.)
Post: #1
CUYI plotter cutter
hi boss, having an issue again with my CUYI plotter cutter.

this time it is responding, it moves left right forward backwards.. but the needle part wont go down. thus, it cant cut the vinyl laid under it..

need immediate support. i do have pending jobs na kelngan tapusin hanggang tom.

here is what i have tried so far.

powercycling the cutter. like 5x already. but still same, the needle wont go down to cut the laid vinyl.

restarted the pc, twice. but it's not on the PC, since the other movements are performed. its just the up down motion for the needle that is not responding.

wala namang error sa PC, or sa flexi8 software.

sinusundan na nga nung cutter yung plot kong design. yun nga lang yung needle part na nag a up and down, yun yung hindi nagrerespond.
so hindi na cucut yung vinyl na nakalatag

here's my shop address

v.santos cor. jp rizal streets, sto nino, marikina city.
here is a screen shot from wikimaps.
[Image: b.png]
just at the right of marikina LTO [if you look at the picture] at the red arrow.
and here is the link to that screen shot. Zen Custom Prints

landmarks near my shop.
-Marikina LTO
-Builders Bank
-Baliwag Lechon Manok
-Lotto
-videobee appliance center

THANKS!
[Image: sig-zenebiercopy.jpg]
Find all posts by this user
Quote this message in a reply
02-16-2012, 07:01 PM
Post: #2
RE: CUYI plotter cutter
naku bakit walang reply? nsan ang after sale support? interesado pa naman ako bumili. hanap hanap muna ako sa mga forum na maganda ang after sale support Sad
(04-27-2011 11:39 AM)zenebier Wrote:  hi boss, having an issue again with my CUYI plotter cutter.

this time it is responding, it moves left right forward backwards.. but the needle part wont go down. thus, it cant cut the vinyl laid under it..

need immediate support. i do have pending jobs na kelngan tapusin hanggang tom.

here is what i have tried so far.

powercycling the cutter. like 5x already. but still same, the needle wont go down to cut the laid vinyl.

restarted the pc, twice. but it's not on the PC, since the other movements are performed. its just the up down motion for the needle that is not responding.

wala namang error sa PC, or sa flexi8 software.

sinusundan na nga nung cutter yung plot kong design. yun nga lang yung needle part na nag a up and down, yun yung hindi nagrerespond.
so hindi na cucut yung vinyl na nakalatag

here's my shop address

v.santos cor. jp rizal streets, sto nino, marikina city.
here is a screen shot from wikimaps.
[Image: b.png]
just at the right of marikina LTO [if you look at the picture] at the red arrow.
and here is the link to that screen shot. Zen Custom Prints

landmarks near my shop.
-Marikina LTO
-Builders Bank
-Baliwag Lechon Manok
-Lotto
-videobee appliance center

THANKS!
Find all posts by this user
Quote this message in a reply
02-19-2012, 07:13 PM
Post: #3
RE: CUYI plotter cutter
(02-16-2012 07:01 PM)snake23 Wrote:  naku bakit walang reply? nsan ang after sale support? interesado pa naman ako bumili. hanap hanap muna ako sa mga forum na maganda ang after sale support Sad

sir sensiya na po mejo busy lang po..... may mga contact numbers din po kami dito.... mejo nagloko lang ang internet namin kaya nde kami naka reply agad.... please po do not jump into conclusion.... thanks din po.... you may contact us din po sa mga numbers nakalagay sa contact us po...

Smile thank you very much po...
Visit this user's website Find all posts by this user
Quote this message in a reply
02-19-2012, 07:18 PM
Post: #4
RE: CUYI plotter cutter
(02-16-2012 07:01 PM)snake23 Wrote:  naku bakit walang reply? nsan ang after sale support? interesado pa naman ako bumili. hanap hanap muna ako sa mga forum na maganda ang after sale support Sad
(04-27-2011 11:39 AM)zenebier Wrote:  hi boss, having an issue again with my CUYI plotter cutter.

this time it is responding, it moves left right forward backwards.. but the needle part wont go down. thus, it cant cut the vinyl laid under it..

need immediate support. i do have pending jobs na kelngan tapusin hanggang tom.

here is what i have tried so far.

powercycling the cutter. like 5x already. but still same, the needle wont go down to cut the laid vinyl.

restarted the pc, twice. but it's not on the PC, since the other movements are performed. its just the up down motion for the needle that is not responding.

wala namang error sa PC, or sa flexi8 software.

sinusundan na nga nung cutter yung plot kong design. yun nga lang yung needle part na nag a up and down, yun yung hindi nagrerespond.
so hindi na cucut yung vinyl na nakalatag

here's my shop address

v.santos cor. jp rizal streets, sto nino, marikina city.
here is a screen shot from wikimaps.
[Image: b.png]
just at the right of marikina LTO [if you look at the picture] at the red arrow.
and here is the link to that screen shot. Zen Custom Prints

landmarks near my shop.
-Marikina LTO
-Builders Bank
-Baliwag Lechon Manok
-Lotto
-videobee appliance center

THANKS!

sir snake..... wala po kami reply dito kase po on the spot na kami nagpunta sa kanya you may contact him po kung ano po ang services na ginawa namin sa kanya..... regarding din po sa problema nang nag post nito.... it is already been solved po......
Visit this user's website Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 1 Guest(s)